Showing posts with label motorcycle rectifier. Show all posts
Showing posts with label motorcycle rectifier. Show all posts
Tuesday, October 20, 2015
Voltage regulator, A summary
Before attempting to use all circuits here regarding voltage regulator for motorcycles, let us first differentiate the two system. Not all machine are the same especially with the design of the voltage regulator. There are single phase system that uses half and full wave charging system, and three phase system that uses half wave system..By looking at this block diagrams, you will be able to determine what system your bike uses by following the connection. FJPGVS6ZRZW7
First and foremost, the single phase, the picture above illustrates a single system half wave regulation, you can see that the one end of the stator is connected to ground, via earth ground, the coil has also a center tap on the winding for your headlight and the output will also be regulated by the voltage regulator..this kind of regulator is a single phase half wave system, if the end of the winding is no where connected to ground then the system will be a full wave.
Read more »
First and foremost, the single phase, the picture above illustrates a single system half wave regulation, you can see that the one end of the stator is connected to ground, via earth ground, the coil has also a center tap on the winding for your headlight and the output will also be regulated by the voltage regulator..this kind of regulator is a single phase half wave system, if the end of the winding is no where connected to ground then the system will be a full wave.
FULL WAVE regulator schematic
A full wave regulator is a type of regulator mostly found on small motorcycle that can enhance the charging system of motorcycle battery. It can be bought in a four pin or in a five pin configuration as shown on the left. It is also being used widely by enthusiast that convert their single phase half wave generator onto a full wave by altering the stator windings.
Wondering what is inside this kind of regulator and how it differs from those commonly used HALF wave regulator, you are in luck for i have the time and resources to open up this donor regulator. it took me hours of heating up, scraping the coating to expose the main board and parts.
Here it is.
with the help of a portable blow torch, soldering iron, a small flat screwdriver, and a bit of patience, I carefully removed the top coating of this regulator exposing the bottom of the PCB. and noticed the smd (surface mount devices). Seeing that makes me more careful of not scrapping them from their location.
Patience is the key when doing this kind of hobby.
HOURS later,
Have to desolder first all components to pull out the pcb.
The bridge rectifier that needs to be heatsinked.
the epoxy residue..(too tough to scrape)
top view
side view
back view
And the schematic of this board
By comparing this to my previous post
Single Phase Shunt Regulator (full wave)
They are almost identical, but as i have said, the regulator above is a five wire type, the schematic shown on left is a four pin type. The difference, the circuit within the link is always connected to the battery thus leakage is present. while as this regulator has a wire (BLACK) that is connected after the ignition switch and not directly to the battery.
It was used for one reason:
1. when ignition off, monitoring circuit of the schematic is disabled, no current will be taken from the battery when stored, or park.
We have a saying " its better to have more than to have enough" This particular five wire regulators can be used on four wire type. just connect the black and red together..
By looking at the schematic, and comparing it to my previous post of voltage regulators, it is almost identical, with the design, and only component values are different. C1, R1, Q1, D1, and R3 compromising the sensing and regulating circuit, whereas D2,D3, Q2 and Q3 are the shunting components of the stator winding.
D4 to D7 are your rectifiers that converts the AC coming from the stator to DC for charging your battery. With the values as shown, the output of this regulator is 14.4 at 5000rpm. You can modify this circuit for your intended application, to output 15 volts rather than 14.4 for quick charging of your battery when there are too much load on your system, by altering D1, to 13 volts rather than 12.6 volts..
This system is Stator dependent...meaning, this can't output more power on what your stator can give, all charging system power rely on your stator max output...
Note: further again..the generator to be used here do not touch the ground or not connected to any ground.
Read more »
Wondering what is inside this kind of regulator and how it differs from those commonly used HALF wave regulator, you are in luck for i have the time and resources to open up this donor regulator. it took me hours of heating up, scraping the coating to expose the main board and parts.
Here it is.
with the help of a portable blow torch, soldering iron, a small flat screwdriver, and a bit of patience, I carefully removed the top coating of this regulator exposing the bottom of the PCB. and noticed the smd (surface mount devices). Seeing that makes me more careful of not scrapping them from their location.
Patience is the key when doing this kind of hobby.
HOURS later,
Have to desolder first all components to pull out the pcb.
The bridge rectifier that needs to be heatsinked.
the epoxy residue..(too tough to scrape)
top view
side view
back view
And the schematic of this board
By comparing this to my previous post
Single Phase Shunt Regulator (full wave)
They are almost identical, but as i have said, the regulator above is a five wire type, the schematic shown on left is a four pin type. The difference, the circuit within the link is always connected to the battery thus leakage is present. while as this regulator has a wire (BLACK) that is connected after the ignition switch and not directly to the battery.
It was used for one reason:
1. when ignition off, monitoring circuit of the schematic is disabled, no current will be taken from the battery when stored, or park.
We have a saying " its better to have more than to have enough" This particular five wire regulators can be used on four wire type. just connect the black and red together..
By looking at the schematic, and comparing it to my previous post of voltage regulators, it is almost identical, with the design, and only component values are different. C1, R1, Q1, D1, and R3 compromising the sensing and regulating circuit, whereas D2,D3, Q2 and Q3 are the shunting components of the stator winding.
D4 to D7 are your rectifiers that converts the AC coming from the stator to DC for charging your battery. With the values as shown, the output of this regulator is 14.4 at 5000rpm. You can modify this circuit for your intended application, to output 15 volts rather than 14.4 for quick charging of your battery when there are too much load on your system, by altering D1, to 13 volts rather than 12.6 volts..
This system is Stator dependent...meaning, this can't output more power on what your stator can give, all charging system power rely on your stator max output...
Note: further again..the generator to be used here do not touch the ground or not connected to any ground.
FET type motorcycle voltage regulator
This is another voltage regulator for motorcycles that uses Field Effect Transistor for better charging efficiency of the system, although still using half wave bridge system on charging the battery, the control to which the system monitors the battery condition. What makes it better is that is a MOSFET controlled device rather than the crude SCR shunt type that is on most bikes until recently and also is a 50A rated device.
MUCH better voltage regulation and runs cooler too due to more efficient devices and control circuitry.The SCR shunt type consumes more energy in the Regulator itself than the bike is using and dumps a ton of current into the heatsink (feel yours & just see how hot those things run!!!! - don't touch it - you'll burn yourself - seriously!) The problem is exacerbated because their efficiency goes even lower when they get HOT so it's a vicious circle. Heat is the number 1 killer of these devices.
Incidentally its a misconception that shunt type work harder with increased load i.e. higher-wattage lights, etc - actually, the higher the load on the output, the less work the shunt regulator does in dumping that excess energy and will actually run cooler!!
The FET has extremely low resistance in conducting state and this results in a lower dissipated power from the device while conducting load current, as opposed to the SCR which shunts the maximum current across a significant volt drop, resulting in a higher dissipated power - and resulting temperature, much more so than the FET device.
Read more »
MUCH better voltage regulation and runs cooler too due to more efficient devices and control circuitry.The SCR shunt type consumes more energy in the Regulator itself than the bike is using and dumps a ton of current into the heatsink (feel yours & just see how hot those things run!!!! - don't touch it - you'll burn yourself - seriously!) The problem is exacerbated because their efficiency goes even lower when they get HOT so it's a vicious circle. Heat is the number 1 killer of these devices.
Incidentally its a misconception that shunt type work harder with increased load i.e. higher-wattage lights, etc - actually, the higher the load on the output, the less work the shunt regulator does in dumping that excess energy and will actually run cooler!!
The FET has extremely low resistance in conducting state and this results in a lower dissipated power from the device while conducting load current, as opposed to the SCR which shunts the maximum current across a significant volt drop, resulting in a higher dissipated power - and resulting temperature, much more so than the FET device.
The picture shows a typical FET type voltage regulator for motorcycles, as opposed to the SHUNT type to where an SCR is used to control the windings to generate more than enough on the system, here an FET is used tag as Q5 in the diagram, IC2a is the control circuitry of the battery charge and discharge. D1 and D2 is the rectifier that converts the AC voltage of the stator to DC that charges the battery.
Single phase shunt regulator again.
Motorcycle voltage regulator commonly uses shunt type in order to control the output of the generator. Shunting the winding to ground is easier than controlling the output of the regulator by those series type.
Circuit on the left is still a shunt regulator controlling the windings, with parts easily obtainable from your local electronic supply stores.
CIRCUIT DESCRIPTION:
D2 and D1 are the SCR that will control the voltage output of the generator, as the rpm of the engine rises D4 and D5 will convert the AC to DC and shall charge the battery, as the battery is being charged, it is been monitored by Q1, R1, D3 and R4 that comprises the voltage threshold of the entire unit and must be adjusted to 14.4 volts cut off. When the sense circuit seen the voltage rises, Q1 will be turned ON and current will then flow towards the gate of the two SCR turning them on thus shunting the windings not to generate more than needed, protecting the battery from overcharging.
NOTE that this circuit do not have a HEADLIGHT controlling device and or headlight regulator, its for charging battery only on motorcycles with stator.
Read more »
Circuit on the left is still a shunt regulator controlling the windings, with parts easily obtainable from your local electronic supply stores.
CIRCUIT DESCRIPTION:
D2 and D1 are the SCR that will control the voltage output of the generator, as the rpm of the engine rises D4 and D5 will convert the AC to DC and shall charge the battery, as the battery is being charged, it is been monitored by Q1, R1, D3 and R4 that comprises the voltage threshold of the entire unit and must be adjusted to 14.4 volts cut off. When the sense circuit seen the voltage rises, Q1 will be turned ON and current will then flow towards the gate of the two SCR turning them on thus shunting the windings not to generate more than needed, protecting the battery from overcharging.
NOTE that this circuit do not have a HEADLIGHT controlling device and or headlight regulator, its for charging battery only on motorcycles with stator.
Subscribe to:
Posts (Atom)











